1. Th8320r1003 Installation Manual

Owner's Regular Proprietor's Manual DS/DSV/RS Beds010-080 Series Dehumidifier Diagnostics - Control Operation SYMPTOM POSSIBLE Trigger CHECKS Actions Code #9 Large control evaporator. (Over 80°Y for 5 minutes) 3. Incorrectly altered or defective hotgas bypass control device (units with A/Chemical only) 4. Excessive air stream 5 Excessive weight 6. Improper return-air duct connection at unit (age.h., 90° elbow very close to the unit) Uneven air distribution across the evaporator and bypass damper prevents normal atmosphere cooling.

I was trying to find the service manual for dectron unit m/n ds040-203 online at dectron site but had no success. Installation & Practice. Service Manual HT800 DECTRON Installation Software HT800 DECTRON Schematics HT800 DECTRON Spare Parts (IPL). Jul 27, 2011  i was trying to find the service manual for dectron unit m/n ds040-203 online at dectron site but had no success, does anyone know how to find it? Thanks, dixie dectron - service manual?

This product line is designed for environments in which humidity can be effectively controlled by ventilation. The Dry-O-Tron DM Series enjoys all the technology, quality and design innovations of our mechanical refrigeration product lines, but without the compressors. Terms of Access This site contains files, documents, and software that are the sole property of Dectron Inc. The use of any of these materials including access to this site is subject to the following conditions.

Check to notice if series from sizzling fuel bypass valve to provider is sizzling. Verify that thé three-way device may end up being jammed: 1. Force the think device to run and check for adjustments in working temperature ranges and stresses. If no adjustments occur, after that the valve is totally crammed and must become changed. If the unit runs fine in swimming pool heating and/or A/M, excursions on higher pressure in dehumidification mode, and also runs with increased than normal pressures in A/D alone, then the pool heating system three-way control device is not shifting totally out of pool high temperature. (This is definitely assuming that no various other cause for a high pressure vacation can become discovered.

If the device runs properly in pool heating and A/G, excursions on higher stress in dehumidifica tion, and runs increased than regular stresses in swimming pool heat by itself, after that the A new/C three-way control device is not really shifting totally out of surroundings conditioning. Replace the defective valve. Examine heat range differential across évaporator. It should become 30° - 35°Y @ 80° - 85°Y, 50% L/H. Adjust electric motor pulley appropriately.

Room temperatures is usually over 90°F / 80% R/H. To keep the unit running, briefly remove cables 11 12 from the We/O plank terminals 11 12. Connect a 10k 12k ¼W resistor between terminals 11 12. Return wires to regular as soon as problems return to regular. Correct improper duct. Notice Installation area of this manual for appropriate duct style. Data subject to modify without see.

Dectron, Inc. May 2005 93 DS/DSV/RS 010-080 Collection Dehumidifier Proprietor's Manual Operation Diagnostics - Controller SYMPTOM Probable CAUSE Investigations ACTION Code #9 High-limit evaporator. (Over 80°Y for 5 mins).extension 7. Defective power mind on thermal expansion valve 8. Sensor out of calibration 9. Defective chilled-air heat range sensor.

Location sensing bulb in frosty water, and after that warm it up in your hands. A fast suction collection pressure change should take place. If not, power head is defective. Replace energy head if possible. If not, replace control device. Get in touch with Dectron or á Dectron-certified technician.

Observe Sensor Calibration. Contact Dectron or á Dectron-certified technician. Order a new sensor. To maintain the device running, in the short term remove cables 11 12 from the I actually/O plank terminals 11 12. Connect a 10k 12k ¼W resistor between terminaIs 11 12. Replace the sensor simply because quickly as feasible. Code #10 Lower control evaporator.

(Below 20°Y for 3 minutes) 1. Insufficient air flow 2. Insufficient fill 3. Improper return-air duct connection at device, e.h., 90° elbow very close to the device. Uneven air submission across the evaporator and get around damper helps prevent normal air cooling. Examine heat range differential across évaporator. It should be 30° - 35°Y @ 80° - 85°N, 50% R/H.

Change electric motor pulley appropriately. Room temperature below 75°Y and/or beIow 40% R/H. Adapt room arranged factors per the CSA/ETL label. Correct incorrect duct.

See Installation section of this manual for correct duct style. Chilled-air sénsor out of caIibration 5. Chilled-air sensor defective. Notice Procedure - Sensor Calibration. Order a new sensor.

To keep the unit running, temporarily remove wires 11 12 from the I actually/O table terminals 11 12. Link a 10k 12k ¼W resistor between terminaIs 11 12.

Th8320r1003 Installation Manual

Replace the sensor simply because soon as possible. Data subject matter to modify without notice. 94 Dectron, Inc.